 Multi-Tile Steel Roofing PanelsThese latest steel roof sheets are sculptured to form a row of 6 ridges to each panel, with there weather proofing lip at the top and bottom edges these are easy to install and look amazing.
Each panel gives a cover size of 1100mm wide x 350mm deep, the actual size is 1180mm wide x 380mm deep.
These sheets have advantages over the standard steel roof sheets in so much as they are alot easier and lighter to handle with the added advantage of being able to slide over each other down the fall of the roof trimming the sheet to the required length is no longer required.
|
 |
|
|
|
|
|
|
 Merlin Grey Corrugated Steel SheetsMerlin Grey Sheets have a CA 32/100 profile, One of the most common steel profiles. All sheets are 0.5mm fully galvanised steel sheets with a "Colorcoat Plastisol" coating this gives the sheet double protecting against the elements for a long lasting stylish roof.
All sheets are 1080mm wide giving a cover width of 1000mm |
|
|
|
|
|
|
|
 Goosewing Grey Steel Corrugated SheetsGoosewing Grey Steel Corrugated Sheets have a CA 32/100 profile, One of the most common steel profiles. All sheets are 0.5mm fully galvanised steel sheets with a "Colorcoat Plastisol" coating, this gives the sheet double protecting against the elements for a long lasting stylish roof.
All sheets are 1080mm wide giving a cover width of 1000mm |
|
|
|
|
|
|
|
 Olive Green Steel Corrugated SheetsOlive Green Steel Corrugated Sheets have a CA 32/100 profile, One of the most common steel profiles. All sheets are 0.5mm fully galvanised steel sheets with a "Colorcoat Plastisol" coating, this gives the sheet double protecting against the elements for a long lasting stylish roof.
All sheets are 1080mm wide giving a cover width of 1000mm |
|
|
|
|
|
|
|
Van Dyke Brown Steel Corrugated SheetsVan Dyke Brown Steel Corrugated Sheets have a CA 32/100 profile, One of the most common steel profiles. All sheets are 0.5mm fully galvanised steel sheets with a "Colorcoat Plastisol" coating, this gives the sheet double protecting against the elements for a long lasting stylish roof.
All sheets are 1080mm wide giving a cover width of 1000mm |
|
|
|
|
|
|
|
 Terracotta Maxi-Tile Steel Corrugated SheetsTerracotta Maxi-Tile Steel Corrugated Sheets have a sculptured appearance giving the effect of solid roof tiles. All sheets are 0.7mm fully galvanised steel sheets with a plastisol coating, this gives the sheet double protecting against the elements for a long lasting stylish roof.
All sheets are 1080mm wide giving a cover width of 1000mm
And are only 6.75Kg/M2 |
|
 Right Angle TrimThese colour matched trims are ideal for finishing the edge of your roof. If using these sheets to clad the side of a building then use these trims to finish the corners. |
|
|
|
|
|
|
|
|
|
|
|
 Edge TrimThese colour matched trims are ideal for finishing the edge of your roof. With the extra bend to fit into the drainage chanel to help prevent rain being blown under the trim. If using these sheets to clad the side of a building then use these trims to finish the corners. |
|
|
|
|
|
|
|
|
|
|
|
 Flashing TrimThese colour matched trims are ideal for finishing the top edge where the sheets meet the host wall. When used with the appropriate eaves fillers you can achieve a draft & water tight seal. |
|
|
|
|
|
|
|
|
|
|
|
 Ridge TrimThese colour matched trims are ideal for finishing the top edge when you have a pitched roof. When used with the appropriate eaves fillers on eother side of the ridge you can achieve a draft & water tight seal. |
|
|
|
|
|
|
|
|
|
|
|
 Suggested Fixing PointsWhen fixing steel sheets it is advised that you fix either side of the vertical joint and at least three points across the the width of the sheets. Additional fixing are required along the length of the sheet at a maximum spacing of 1000mm between fixings |
|
 Tapfix Fixings (pk10)The fixings have a 19mm Sealing Washer and are used to secure the sheets to timber frames. avaliable in 32mm, 50mm & 75mm lengths, coloured caps not included, please see below. |
|
|
|
|
|
|
|
 Clad Fix Drill & Tap Fixings (pk10)The fixings have a 19mm Sealing Washer and a unique self drill design. And can be used to secure the sheets to either metal or timber frames. avaliable in 20mm, 38mm, 50mm & 70mm lengths, coloured caps not included, please see below. |
|
|
|
|
|
|
|
|
|
Tapfix & Cladfix Coloured CapsFor use with both Tapfix & Clad Fix fixings, these packs of 10 colour coded caps clip onto the fixing screws to cover the hexagond head and sealing washer. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Conversions UtilityPlease Note This Utility Is For Guidance Only. C & A Building Plastics Cannot Be Held Responsible For Any Inaccuracies.
|
|
| Metric To Imperial Imperial To Metric |
|
|
|
|
Important NoticeAll Plastic Building Materials should be kept flat during transport and storage. If the items are to be stacked then care must be taken not to overload the stack so as to crush the lower products, it it extremely important that all materials are covered with a LIGHT PROOF sheet to prevent direct sunlight over heating the interior of the stack. |
|
